Tickets now on sale

Secure Your Spot
learn more

Resin Jointing Compound

GftK vdw 833

Resin Jointing Compound (VDW 833) resin jointing compound is a great choice for small-format natural stone and concrete pavers in areas that see medium to heavy traffic. Unlike poly sand or wet sand, you can apply this resin jointing compound on your driveway!

Order Online
become A Dealer
VDW 833 Resin Jointing Compound
DSC03045 1
MG 8083 1

Why Use The VDW 833 Resin Jointing Compound?

water permeable for vdw 833

Fully Water Permeable

 You might be thinking that a drawback to these products would be that they are non-pervious, but it’s actually the opposite. Not only is the VDW 833 Resin Jointing Compound durable, but it’s also permeable!

applicable in rain for vdw 833

Applicable in Rain

Another amazing feature of GftK products is that they can be applied to your patio or driveway in the rain. No more putting off jobs and missing paydays because of weather conditions. They work just as well applied wet.

self compacting for vdw 833

Self-Compacting

With any Joint Compound, having it be self-compacting allows for increased strength by minimizing voids between pavers. This creates a tighter bond and seal!
With this feature, there is no need for additional compacting equipment during installation.

long lifespan for vdw 833

Long Lifespan

One of the best features of the VDW 833 Resin Jointing Compound is its durability and strength. Although this 2-part resin line is more expensive than poly or wet sand, it actually is a better investment long term as they’ll last you for 20+ years. And with little to no maintenance required, you actually pay less in the long run

VDW 833 Resin Jointing Compound

Technical Product Data

Product Size11 lb epoxy kit to mix with 55 lb bag of sand
Application TimeApprox. 1 hr at 20°C | 68°F application temp
E-Modulus8,500 N/mm2
Flexural StrengthApprox. 15,0 N/mm2 / 2175 psi
Dry Density8.0 N/mm / 1160 psi
Set mortar density: 1,62 g/cm3
Application Temp.2-26°C | 37-80°F (Do not lay onto frozen ground.)
Compressive Strength Approx. 45,0 N/mm2 / 6520 psi
Water Permeability2,0 x 10-5 m/s (0,23 l/m2 /min at 20% joints)
Storage Life1 year if stored unopened in sealed and undamaged packaging. Must also be kept dry and frost-free.
Download the full spec sheet

Recommended Mixing Tools:
Option 1: 3-Piece Cone Mixing Kit

The Superior 3-Piece Cone Mixing System is an excellent mixing option exclusively designed for our two-part resin joint compounds.

Learn More
Buy Now

Recommended Mixing Tools:
Option 2: X055 Double Paddle Mixer

This Dual Paddle Mixer Offers the Highest quality materials and the finest German engineering. It’s the most reliable product on the construction site. Proven hundreds of thousands of times on job sites all over the world.
*To be Mixed in the Collomix 8 or 9 gallon buckets*

Learn More
Buy Now

Recommended Application Tools:
Brooms and Squeegee Bundle

The 3-Piece Brooms & Squeegee Bundle is all the tools you need for clean and easy 3-part installation of any 2-part Epoxy all in one place.
Suitable for all GftK products except VDW 480 and VDW 495

Learn More
Buy Now

Application Instructions for Resin Jointing Compound VDW 833

1

Construction Site Requirements

  • A stable, load-bearing structure, a water-permeable sub-base and the paving layer must all be correctly designed and installed for the anticipated traffic loads and in accordance with AMTS.
  • VDW 833N Grouting Binder is designed for small up to large format and cannot be used to compensate any settlement of the substructure, or for the sealing and waterproofing of any surfaces. Movement joints must be installed as necessary to comply with the required structural design and any anticipated levels of movement.
  • The VDW 833 Grouting Binder can be applied on damp / wet paving and in high humidity and even in the rain.

2

Preparation

Preparation / Pre-wetting:

  1. Clean the surface thoroughly of all dirt, cement residues, organic materials or any other possible contaminants including cleaning out all of the joints to the required depth.
  2. Thoroughly pre-wet the surface of the paving and mask adjacent surfaces which are not to be jointed. Always use clean and fresh tap water!

3

Mixing & Filling the Joints

  • Open your SHS 55 lb bag of sand and pour it into a pail or an appropriate mixer such as the SHS Distributors cone mixer. Add (component A and B) of the VDW 833 N Grouting Binder liquid from the bottles into the pail or mixer and mix for 3 to 5 minutes until smooth and homogeneous. Proper mixing is important!
  • When mixing in a pail use the appropriate spherical paddle mixer or SHS superior auger mixer to insure a properly mixed end product. Any material that is not thoroughly mixed must not be used. No water should be added during the mixing process.
  • Apply immediately after mixing, by pouring the VDW 833N Grouting Binder directly onto the pre-wetted surface. Work the self-compacting material thoroughly into the joints using a rubber squeegee.
  • If the viscosity of the product diminishes re-moisten by spraying lightly with water from a hose. The paved area must be kept constantly wet during application. We recommend working from the highest to the lowest points.
  • Do not mix part units of the product. Any unmixed material must not be used.

4

Brushing Off

  • Remove any excess VDW 833 N Grouting Binder residue from the area after about 5 min. (immediately at temperatures over 20 °C / 68 °F) spraying lightly with water from a hose at a distance of about 25 cm. Avoid washing material out of the joints.
  • Be careful to clean the paved surface towards areas not yet jointed and do not allow any water containing residues to pond, stand, dry out or run-off over completed areas.
  • Finally remove any remaining fine residues, again with a damp coconut fiber brush – do not brush any residual dry material into any unfilled joints. Clean this brush in water frequently.

5

Important Information

  • Remain off the freshly applied areas for a period of min. 24 hours, or until the paving surface is no longer tacky. Then the areas can be walked over. The area can be fully released to vehicular traffic after 3 – 5 days, when fully hardened.
  • In general, a strength test should be carried out before final clearance of the area. A very thin film of the resin binder will remain on rough surfaces or any surfaces that are not cleaned thoroughly. This film will disappear after a period of exposure to traffic and weathering.
Order Now
Become A Dealer

GFTK Consumption Calculator

Use This GFTK calculator to find out how much product you need!



Please Note For The Calculator:
Calculations will only occur if all fields are filled in correctly.
Please ensure that a 0. is listed where the dimensions are under an inch.

For The Xtreme Elutriant: 
Coverage is approximately 75 sq ft per bag of VDW 495.
Please View This PDF for Additional Information

Shop more GftK Jointing Products