The GFTK Xtreme Stone Protect 3-in-1 VDW 950
$185.23
- Water-based formula
- Invisible
- For natural stone and concrete pavers
- Grouting relief for subsequent jointing with an epoxy binder
- Suitable for use on sensitive stones before jointing to reduce staining
- Hydrophobic – water repellent
- Oleophobic – oil-repellent
- Solvent-free
The GFTK Xtreme Stone Protect 3-in-1 VDW 950 is a ready-to-use, water-based impregnation for the hydrophobic (water-repelling) and oleophobic (oil-repelling) treatment of natural stone and other porous paving units. Can also be used as a pre-treatment before grouting with VDW jointing compounds to reduce any residual binder film on sensitive paving surfaces.
The following are a few specific details about the product:
Water-Based Formula
This Xtreme Protect Formula allows for the same strength needed without the off-gassing that can occur with other products. It does not contain harmful chemicals, solvents, or VOCs that can harm the environment or pose a health risk to anyone exposed.Invisible
This allows you to be worry-free about your project, knowing it’s covered and sealed while allowing you to appreciate all the hard work put into its installation. This keeps the stone looking as natural as possible while offering maximum protection!- Protect areas treated with Xtreme StoneProtect Plus 3 in 1 from moisture and any other dirt or surface contamination for a minimum of 5 hours before access, 24 hours before use (at 20°C/68°F and 65% relative humidity).
- When completely dry, the treated paving can also be pointed with the appropriate VDW jointing mortar, if this was not completed before the treatment.
Water and oil-repellent
Being Water and Oil-repellent allows for maximum protection while including ease and accessability in cleaning any spills that may occur. Hydrophobic (water-repelling) and oleophobic (oil-repelling) allow homeowners peace of mind living in any climate or any installation when using natural stone.For Natural stone and concrete pavers
This treatment is an environmentally friendly choice for tile installations. It is made with eco-friendly materials that reduce its impact on the environment. Its water-based formula allows it to penetrate deep into the stone and protect it from the inside out! Especially for sensitive pavers.Technical Data:
- pH Value:
- Approx. 5
- pH Value:
- Appearance:
- Transparent, slightly yellowish
- Appearance:
- Full Effect:
- After approx. 24 hours at 20 °C / 68 °F and 65 % relative humidity
- Full Effect:
- Storage Life:
- 12 months in original sealed packaging in dry, cool conditions away from frost
- Storage Life:
- Density:
- Approx. 1.0 g/l
- Density:
- Odor:
- Almost odorless
- Odor:
- Pedestrian traffic:
- After about 5 hours at 20°C/68°F and 65% relative humidity
- Pedestrian traffic:
- Duration of effect:
- Approx. 2 years (dependent on the surface type, level of product absorption and exposure)
- Duration of effect:
- Consumption:
- Approx. 5 – 10 m² / liter. (Consumption is highly dependent on the absorbency.
- Consumption:
Application Instructions for GFTK VDW 950 StoneProtect PLus 3 in 1
1. Requirements
- A clean and dust-free, structurally sound, absorbent, and dry paved surface which is otherwise ready for pointing; or with pointing that is fully cured and has no residual binder on the surface.
- Ambient and surface temperatures – minimum 10°C/50°F, maximum 25°C/77°F, with dry weather conditions and no rain or heavy dew forecast for at least 24 hours.
- After application and prior to grouting, thoroughly pre-wet the surface of the paving and mask adjacent surfaces that are not to be jointed.
- Always use clean and fresh tap water!
2. Tools
- Brushes, rollers, or low-pressure sprayers, plus sponges to remove any excess.
- Suitable PPE should be used, including goggles, gloves, etc.
3. Application
- The areas to be treated should be completely dry, clean, and free from any dirt or contaminants that could prevent or reduce penetration.
- Apply VDW 950 StoneProtect Plus 3 in 1 with a suitable brush, roller, or low-pressure sprayer evenly over the surface to saturation, but avoiding any residual ponding or puddling.
- Remove any excess with a sponge; this is particularly important on surfaces with uneven absorbency. Otherwise, localized darkening can occur.
- Avoid splashes on adjacent materials, and remove any spillages immediately with a damp cloth.
4. Curing
- Protect areas treated with Xtreme StoneProtect Plus 3 in 1 from moisture and any other dirt or surface contamination for a minimum of 5 hours before access, 24 hours before use (at 20°C/68°F and 65% relative humidity).
- When completely dry, the treated paving can also be pointed with the appropriate VDW jointing mortar, if this was not completed before the treatment.